PI00004964

These cymbals are made of brass by casting it. They make a sound when clapping each other. -4 inches in length -2.5 inches in diameter of boss

PI00004961

It was casted with the craft of bronze casting. It's played by clashing together holding in each of the hands. -15 inches of cymbal in diameter -3.5 inches in perimeter -8 inches of dome of cymbal

PI00004962

It's made of woods such as jackfruit, mango, MèYone, Yamanay, Linzin etc. For the drum shell, a straight and level trunk of a tree is cut in a desired measure and carved in a hollow. The wood has to be treated with heat for about half a day not to be destroyed by wood eaten insects. Then, the cattle skin is stretched taut over the both heads of the drum shell. The leather bands are used to hold a balance between the loosing and the tightening of skin during it is stretched over the heads of drum. It's played by striking over the stretched leather with the hands or with the stick. Sometimes, it's accompanied by a gong set. -3 feet of long drum in diameter -14 inches of leather surface in diameter -4.4 feet of leather surface in circumference -22 inches of long drum shell in circumference -4.3 feet of long drum base in circumference

PI00004960

It's made of woods such as jackfruit, mango, MèYone, Yamanay, Linzin etc. For the drum shell, a straight and level trunk of a tree is cut in a desired measure and carved in a hollow. The wood has to be treated with heat for about half a day not to be destroyed by wood eaten insects. Then, the cattle skin is stretched taut over the both heads of the drum shell. The leather bands are used to hold a balance between the loosing and the tightening of skin during it is stretched over the heads of drum. It's played by striking over the stretched leather with the hands or with the stick. Sometimes, it's accompanied by a gong set. -18 inches of drum in diameter -3 feet inches circumference -11 inches of leather surface in diameter

PI00004963

Two pieces of Thaik bamboo are cut in desired measure and a piece of LatPhatTaung bamboo is also cut in desired measure to use as the middle joint. The middle joint piece of bamboo is made a hole with a small knife and put a reed on it. Then, the two pieces of Thaik bamboo are fixed to the middle joint of LatPhatTaung bamboo from both ends. Blow at the mouth-hole of the middle joint bamboo opening and shutting at the holes of two other bamboos by the thumbs. The left sided bamboo produces the high pitch and the right sided bamboo does the low pitch. Up to five pitches can be blown with it. Usually, it's blown accompanying with the gongs and cymbals. -15 inches of left bamboo in length -2 inches of left bamboo in circumference -13 inches of right bamboo in length -2 inches of right bamboo in circumference -5 inches of the middle joint bamboo in length -2.5 inches of the middle joint bamboo in circumference -1.5 inches of mouth-hole in length -0.5 inches of mouth-hole in width

PI00004965

It is made of brass by casting it. They make a sound when striking its surface. -1 feet 3 inches in length -2 inches in thickness -4 inches in diameter of boss

PI00004966

It is made of brass by casting it. They make a sound when striking its surface. -1 feet in length -1.5 inches in thickness -1 inch in diameter of boss

PI00004967

It is made of brass by casting it. They make a sound when striking its surface. -8 inches in length -1.5 inches in thickness -1 inch in diameter of boss

PI00004968

It is made of brass by casting it. They make a sound when striking its surface. -6.5 inches in length -0.75 inches in thickness -0.75 inches in diameter of boss

PI00004969

It is made of brass by casting it. They make a sound when striking its surface. -5 feet in length -0.75 inches in thickness -0.75 inches in diameter of boss

PI00004970

It is made of brass by casting it. They make a sound when striking its surface. -4 feet in length -0.75 inches in thickness -0.75 inches in diameter of boss